CF-19 time!!!!!!

Post all questions and information about the CF-19 in here.
Message
Author
User avatar
Bill_TN
Posts: 531
Joined: Sat Mar 21, 2015 9:07 am
Location: Ft. Campbell area.

Re: CF-19 time!!!!!!

#21 Post by Bill_TN »

Yea and at almost 200.00 for 2x4gb ram I'll probably stay at 32 bit. So be it.
CF-29ET, CF-28ST, CF-30G , CF-M34, CF-19Ch, CF-19FH, CF-19CD, CF-73 mk1, CF-74K & H, CF-51RCB, CF-51RCL, CF-52CC .

As long as the deal is good for you it is good for me.

Member of Toughbooktalk and Notebook Review forums

User avatar
ADOR
Posts: 1990
Joined: Tue Dec 21, 2010 12:51 pm
Location: Northeast Louisiana

Re: CF-19 time!!!!!!

#22 Post by ADOR »

I loaded 64 bit 7 on a MK2 about 3 years ago. It had 4 gb ram and my standard OS tweaks. It seemed to run fine but it had a X2 intel sd as well.
CF-28 MK2,Mk3 / CF-29 Mk3 / CF-30 MK2 / CF-25 Mk1 ATI / CF-19 MK3/Mk3/Mk5 / CF-U1 Mk1,Mk2 / CF-M34 Mk7/Mk3 / CF-17 Mk1 / CF-07
Voodoo Envy M355 / M360 / M515 / M780 / U703 / Voodoo Hexx / Voodoo Idol / Voodoo Rage F1 / Voodoo Rage F1 / Voodoo Rage F1 "signed case" / Voodoo Omen
Alienware M11x R1, Alienware 17 R5

User avatar
Bill_TN
Posts: 531
Joined: Sat Mar 21, 2015 9:07 am
Location: Ft. Campbell area.

Re: CF-19 time!!!!!!

#23 Post by Bill_TN »

Well since I'm finally getting in the vehicle diagnostic software that I've been wanting, I'll be taking this install a bit more serious than usual. My Cat , OBED2, light/heavy trucks, Alision trans, and Bendix software.
CF-29ET, CF-28ST, CF-30G , CF-M34, CF-19Ch, CF-19FH, CF-19CD, CF-73 mk1, CF-74K & H, CF-51RCB, CF-51RCL, CF-52CC .

As long as the deal is good for you it is good for me.

Member of Toughbooktalk and Notebook Review forums

User avatar
ADOR
Posts: 1990
Joined: Tue Dec 21, 2010 12:51 pm
Location: Northeast Louisiana

Re: CF-19 time!!!!!!

#24 Post by ADOR »

I use my 30 Mk2 for my OBD reader stuff. Only have a OBD 2 readers. Bluetooth and usb cable. Later on when I can swing the close to 2 grand price I want a self learning EFI for my 52 ford where I can tune is as I drive with my laptop.
CF-28 MK2,Mk3 / CF-29 Mk3 / CF-30 MK2 / CF-25 Mk1 ATI / CF-19 MK3/Mk3/Mk5 / CF-U1 Mk1,Mk2 / CF-M34 Mk7/Mk3 / CF-17 Mk1 / CF-07
Voodoo Envy M355 / M360 / M515 / M780 / U703 / Voodoo Hexx / Voodoo Idol / Voodoo Rage F1 / Voodoo Rage F1 / Voodoo Rage F1 "signed case" / Voodoo Omen
Alienware M11x R1, Alienware 17 R5

User avatar
toughasnails
Toughbooktalk Moderator
Posts: 2644
Joined: Sat Mar 28, 2009 7:59 pm
Location: "TOUGHBOOK LAND" ME ,USA / NB . CANADA

Re: CF-19 time!!!!!!

#25 Post by toughasnails »

Speaking of the 52 Ford. Have not seen no updates on how it's going.
:spinny: Blair :spinny:
___________________
CF-19 MK1, 2, 5 Emissive Keyboard, Samsung 240GB SSD, 12GB Ram, W7 64 bit, GPS *
CF-28 MK2, 3
CF-30 MK2 , Intel SSD, 4GB , GPS, W7 Ultimate , Bluetooth, Emissive Keyboard
CF-51 MK3LL Core 2 Duo T7600 Mod , W7, 4GB Ram, 160GB 7200RPM HDD, Finger Print Reader
CF-52MK1 Core2Duo 2GHz, Intel SSD X25 Series ,4GB , BT with dock
CF-52 MK4 i5‑2540M 2.60GHz, ATI Discrete Graphics, Intel 120GB SSD, 16GB,W7 Pro 64bit
CF-53MK1 i5/2520, Kingston Hyper X SSD 240GB, 16GB memory, W7 Pro 64bit with dock
CF-54 MK2 Samsung SSD512GB, 16GB memory
And the little guys CF-M34 MK3 and MK7
Infologix / MediSlate 10.4" tablet
Cel Samsung Note 8
Member of:
http://thessdreview.com/
http://www.toughbooktalk.com

User avatar
ADOR
Posts: 1990
Joined: Tue Dec 21, 2010 12:51 pm
Location: Northeast Louisiana

Re: CF-19 time!!!!!!

#26 Post by ADOR »

The holidays (turkey day and Christmas) slowed it down. Then last time home the day I got home the wife went into the hospital. Nothing serious but it looks like soon her gallbladder will need to be removed. She talks to the DR about it on the 27th. Right now it's just about ready to put tags on it and put it on the road. I could put tags on it right now if I had too.

The main things right now to finish up are. Cut out plywood kick panels-cut speaker holes-cover and install kick panels, recover main seat (have the materials already), pull out the original lower seat frame extension and make a new custom one from my pile of 1"x1" tubing. I am wanting it where it leans forward and I can use underneath the seat for storage, 10" pioneer comp sub and amp going under the seat.

Since I removed the original behind the seat gas tank from the truck and replaced it with a tank in the bed I am building a storage box behind the seat that opens forward. I have tested the brakes in the yard and up to about 30 to 35 mph but want to get out on the road and test a few panic stops at 55,65 and 75 mph to make sure the manual disk brakes are up to the task. If not I will be doing a swinging pedal from the fire wall. Install heater box and put a 12v to 6v resistor inline to lower the voltage from my 12V system.

I have some holes in the fire wall that I need to weld up, a few pin holes in the floor board as well. Probably use a my brass block as a backer and just fill the hole with my wire welder. It won't stick to the brass. Drill the hood for the hidden hood pins, one head light ring tab is missing, got to cut a 1" x 1/2" sheet metal and weld it to replace the tab, then drill it. Decide if I am mouting the Pioneer radio in the glove box or if I am going to build a over head panel and put it up there. Plug the hole where I cut out for the shiftier and shiftier linkage. Install the carpet.

The list has got short on it. Later on when I improve it I am looking at a rear end swap. I can go with a 9" from a 57 to 73 ford truck and it will bolt right in. Just need to redo shock mounts. If I want something newer I can go with a 8.8 from a 96 up explorer. That would give me rear disk brakes. Those rear ends also have 31 spline axles and a lot of them are 3.73 with a locker. I am looking for another truck to do. If I don't find one I may just not put another straight axle in. I have a complete v12 jaguar IRS/IFS at the house already that is perfect to drop into those trucks. They are so close the jaguar front mounts line up and you can bolt the front spring hangers to it.

Engine wise right now it has a stock 89 Lincoln town car 5.0. It's a standard output model. I have installed a high rise single plane Edelbrock street master intake, 600 cfm edelbrock carb, Carb roller distributor, Vintage MSD 6A box, Shorty headers, 2.5" exhaust, magna flow mufflers, gennie shifter all hooked to a 1977 FMX then outputting to the original Dana 44 rear end with 3.92 rear gears. Tires are 275/60R15 in the rear.

The parts I am swapping onto that engine later on when I know it's going to last. I have to fly cut the true flat top pistons with no valve reliefs to clear the valves(this can be done while still in the truck) Dropping in a .444 lift 1986 mustang gt cam, gt40 3 bar cylinder heads(after I port them) 1.7 cobra roller rockers increasing lift to .472, changing out the front timing cover and installing a fuel pump essentric so I can mount and use a mechanical fuel pump.

You should see the LED light panel I installed where the single bulb went for the interior light. It's so bright it's blinding at night. I also took apart all the dash lights and converted to LED. Tail light, park and turn signals are all LED now.

Here are some pictures on the type of storage I am talking about. It's a smaller regular cab so I need all the space I can get.

http://www.ford-trucks.com/forums/attac ... 1441572456

http://www.duhabin.com/dh-images/03-09- ... uns-lg.jpg

And a few pictures of what it looks like now.

Crap, can't get flickr to come up, pictures coming soon.
CF-28 MK2,Mk3 / CF-29 Mk3 / CF-30 MK2 / CF-25 Mk1 ATI / CF-19 MK3/Mk3/Mk5 / CF-U1 Mk1,Mk2 / CF-M34 Mk7/Mk3 / CF-17 Mk1 / CF-07
Voodoo Envy M355 / M360 / M515 / M780 / U703 / Voodoo Hexx / Voodoo Idol / Voodoo Rage F1 / Voodoo Rage F1 / Voodoo Rage F1 "signed case" / Voodoo Omen
Alienware M11x R1, Alienware 17 R5

User avatar
Shawn
Posts: 2960
Joined: Fri Jan 18, 2013 11:35 am

Re: CF-19 time!!!!!!

#27 Post by Shawn »

very impressive.
Life will beat you into submission.

User avatar
Bill_TN
Posts: 531
Joined: Sat Mar 21, 2015 9:07 am
Location: Ft. Campbell area.

Re: CF-19 time!!!!!!

#28 Post by Bill_TN »

Well have made 2 hdds with Vista on them for the 19 mk2. Crap I think it's the mk2. I remember that it has the best processor at 1.6ghz. Any ways. One hdd is a ssd and the other is a ssd. Both have a 32 bit (because that's all I have right now) vista install on it. Am doing upgrades to serv pack 1 and then 2 on each. Then will do a 7 install to each. 32 bit and 64 bit. See where it goes from there. I'm expecting to have fewer issues with the 32 bit over the 64 bit strictly due to drivers. 32 bit drivers sometimes have issues on 64 bit installs. Either way this is going to be an adventure.
CF-29ET, CF-28ST, CF-30G , CF-M34, CF-19Ch, CF-19FH, CF-19CD, CF-73 mk1, CF-74K & H, CF-51RCB, CF-51RCL, CF-52CC .

As long as the deal is good for you it is good for me.

Member of Toughbooktalk and Notebook Review forums

User avatar
Bill_TN
Posts: 531
Joined: Sat Mar 21, 2015 9:07 am
Location: Ft. Campbell area.

Re: CF-19 time!!!!!!

#29 Post by Bill_TN »

Well so far the diagnostics software is crap.
CF-29ET, CF-28ST, CF-30G , CF-M34, CF-19Ch, CF-19FH, CF-19CD, CF-73 mk1, CF-74K & H, CF-51RCB, CF-51RCL, CF-52CC .

As long as the deal is good for you it is good for me.

Member of Toughbooktalk and Notebook Review forums

Post Reply

Return to “CF-19 Talk (Discontinued Model)”